Notes on LEDs

LED Parts

LEDs come in all shapes and sizes, but the 3mm T-1 or 5mm T-1¾ are the most common.

The die is a small cube of semiconductor.  The composition of the die determines the color of the light given off. The die sits in the top of the die cup, which is a reflector to reflect the light emitted by the die.  The beam angle is determined by the shape of this relector. The epoxy body also is shaped to acts to effect the focus and appearance of the the light beam. The distance from the die cup to the domed end of the lens determines how tightly focused is the resulting beam of light. Some LEDs have flat, opaque,  or even concave ends to help disperse the light into a wide beam.

LED Color

Visible LEDs

LED colors are often specified in "nm", or nanometers, which is the wavelength of the light. The wavelength given is the wavelength at peak output.  LEDs are not perfectly monochromatic, but rather produce a range of wavelengths over a small region of the spectrum. The graph on the left shows color vs. intensity for a typical green LED.  Notice the peak is at about 565 nm, but it is actually emitting light over a range of about 520 nm to 610 nm. Spectral line half-width is the width of this curve at 50% intensity (0.5 on the Y-axis).  For this LED, it is about 30 nm.   Spectral line half-width is a measure of how "pure" (monochromatic) the color is.

Notice the temperature (Ta) given in the upper right corner of the graph. LEDs emit slightly different colors at different temperatures. They also emit different colors at different currents, especially white LEDs which depend on phosphors to change the colored light of the die to white light.

This is why white leds (in particular) will never match perfectly in color.

Infrared LEDs

The infrared band can be divided into Near Infrared (NIR) and Far Infrared (IR). Far infrared is the thermal infrared used to detect hot objects or see heat leaks in buildings, and is way beyond the range of LEDs. (NIR can be further divided into two bands, longwave and shortwave NIR,  based on how film and CCD cameras react.

Infrared LEDs are sometimes called IREDs (Infra Red Emitting Diodes).

Ultraviolet LEDs

Ultraviolet light is divided into three bands: UV-A, which is fairly innocuous; UV-B, which causes sunburns; and UV-C, which kills things. Most UV-B and all UV-C from the sun is filtered out by the ozone layer, so we get very little of it naturally. LEDs emit UV-A.

400 nm is a pretty common wavelength for UV LEDs. This is right on the border between the violet and ultraviolet, so a significant portion of the light emitted is visible. For this reason 400 nm UV LEDs are sometimes rated in millicandela, even though as much as half of their energy is invisible. LEDs with lower wavelengths, such as 380nm, are usually not rated in millicandela, but in milliwatts.

YOU SHOULD NOT STARE INTO ANY LED DUE TO ITS BRIGHTNESS.  MOST LEDS WILL INVOKE PAIN TO THE EYE TO WARN YOU TO LOOK AWAY.  ULTRAVIOLET LEDS ARE PARTICULARLY DANGEROUS, BECAUSE A LARGE PORTION OF THE RADIATION EMITTED IS IN THE VISIBLE RANGE.  THE RESULT IS THAT YOUR EYES WILL NOT INVOKE PAIN TO WARN YOU THAT THEY ARE HARMING YOUR EYES.

White light is a mixture of all the colors. Color "Temperature"  is a misnomer and is not understood by most people.  This is not helped by all the false advertising and hype that is used by marketers to sell their products. Color "Temperature" is a measure of the relative amounts of red or blue light being emitted.  It is not a measure of temperature at all.

Higher color temperatures have more blue. A higher color temperature, is not necessarily an indication of a higher quality, or more expensive light.  It is not a brighter light.  If you want super high color temperature, just buy a blue light.  It is has infinite color temperature which is higher than any "super or hyper" white light.

Kelvin Color Scale

Remember that this is a measure of color, not brightness, so don't freak out because moonlight is "hotter" than a carbon arc! It just means that the color is bluer, that's all.

White and blue LEDs have a color temperature, but leds not in the white-blue spectrum do not.

LED Brightness

The total power consumed by  a light is measured in watts. How bright the object appears, however, will depend on two additional factors:

• how much radiant flux is emitted toward the observer; and
• how sensitive the observer is to the wavelength(s) of the light.

To quantify the first, the steradian, a solid (3-D) sphere is used.

If the radiant flux of a source is radiated uniformly in all directions, the radiant intensity will be simply the total radiant flux divided by 12.57 (4π) steradians, the solid angle of a complete sphere. In the case of LEDs, the radiant flux is usually concentrated into a beam, however, so the radiant intensity will be the radiant flux divided by the solid angle of the beam. Beam angles are usually expressed in degrees, while radiant intensity is usually expressed in mW/sr, making a conversion from beam angle to steradians necessary:

sr = 2 π (1 - cos(θ/2))

where sr is the solid angle in steradians, and θ is the beam angle.

Luminous flux and luminous intensity are measurements like radiant power and radiant intensity, only adjusted for the sensitivity of the human eye. Radiant power of a wavelength of 555 nm is multiplied by a factor of 1, but light of higher and lower wavelengths are multiplied by lower factors, until infrared and ultraviolet wavelengths are reached, when the radiant power is multiplied by zero.

Luminous flux is measured in lumen, while luminous intensity is measured in lumen per steradian, also called a candela.

The relationship between luminous flux, luminous intensity, and beam angle means is that focusing a given LED into a tighter beam (decreasing the beam angle) will increase its luminous intensity (brightness) without actually increasing the luminous flux (amount of light) it puts out. Keep this in mind when buying LEDs for illuminating purposes - a 2000 mcd 30° LED puts out just as much light as am 8000 mcd LED with a 15° viewing angle. (The angle is half in both width and height, so the beam is four times as bright.) This is one of the reasons that ultra-bright LEDs are often "water clear", to keep the light going in one direction and not diffuse it all over the place.

The brightness of LEDs is measured in millicandela (mcd), or thousandths of a candela. Indicator LEDs are typically in the 50 mcd range; "ultra-bright" LEDs can reach 15,000 mcd, or higher (the 617 nm Luxeon Star (part number LXHL-NH94) can reach 825,000 mcd), but the cost is these leds makes them not yet practical for common use.

By way of comparison, a typical 100 watt incandescent bulb puts out around 1700 lumen - if that light is radiated equally in all directions, it will have a brightness of around 135,000 mcd. Focused into a 20° beam, it will have a brightness of around 18,000,000 mcd.

38-11 Illumination

Intensity of light and other electromagnetic radiation as power per unit area, measured in watts per square meter. Similarly, the total rate of radiation of energy from any of the sources of light discussed in Sec. 38-2 is called the radiant power or radiant flux, measured in watts. These quantities are not adequate to measure the visual sensation of brightness, however, for two reasons: First, not all the radiation from a source lies in the visible spectrum; and ordinary incandescent light bulb radiates more energy in the infrared than in the visible spectrum. Second, the eye is not equally sensitive to all wavelengths; a bulb emitting 1 watt of yellow light appears brighter than one emitting one watt of blue light.

The quantity analogous to radiant power, but compensated to include the above effects, is called luminous flux denoted by F. The unit of luminous flux is the lumen, abbreviated lm, defined as that quantity of light emitted by 1/60 cm² surface area of pure platinum at its melting temperature (about 1770°C), within a solid angle of 1 steradian (1 sr). As an example, the total light output (luminous flux) of a 40-watt incandescent light bulb is about 500 lm, while that of a 40-watt fluorescent tube is about 2300 lm.

When luminous flux strikes a surface, the surface is said to be illuminated. The intensity of illumination, analogous to the intensity of electromagnetic radiation (which is power per unit area) is the luminous flux per unit area, called the illuminance, denoted by E. The unit of illuminance is the lumen per square meter, also called the lux:

1 lux = 1 lm/m²

An older unit, the lumen per square foot, or foot-candle, has become obsolete. If luminous flux F falls at a normal incidence on an area A, the illuminance E is given by

E = F ÷ A

Most light sources do not radiate equally in all directions; it is useful to have a quantity that describes the intensity of a source in a specific direction, without using any specific distance from the source. We place the source at the center of an imaginary sphere of radius R. A small area A of the sphere subtends a solid angle [omega] given by [omega]=A÷R². If the luminous flux passing through this area is F, we define the luminous intensity I in the direction of the area as

I = F ÷ [omega]

The unit of luminous intensity is one lumen per steradian, also called one candela, abbreviated cd:

1 cd = 1 lm/sr

The term "luminous intensity" is somewhat misleading. The usual usage of intensity connotes power per unit area, and the intensity of radiation from a point source decreases as the square of distance. Luminous intensity, however, is flux per unit solid angle, not per unit area, and the luminous intensity of a source in a particular direction does not decrease with increasing distance.

EXAMPLE: A certain 100-watt bulb emits a total luminous flux of 1200 lm, distributed uniformly over a hemisphere. Find the illuminance and the luminous intensity at a distance of 1 m, and at 5 m.

SOLUTION: The area of a half-sphere of radius 1 m is

(2[pi])(1 m)² = 6.28 m²

The illuminance at 1 m is

E = 1200 lm ÷ 6.28 m² = 191 lm/m² = 191 lux

Similarly the illuminance at 5 m is

E = 1200 lm ÷ 157 m² = 7.64 lm/m² = 7.64 lux

This is smaller by a factor of 5² than the illuminance at 1 m, and illustrates the inverse-square law for illuminance from a point source.

The solid angle subtended by a hemisphere is 2[pi] sr. The luminous intensity is

I = 1200 lm ÷ 2[pi] sr = 191 lm/sr = 191 cd.

The luminous intensity does not depend on distance.

LED Brightness - IR and UV LEDs

Question: How bright is an IR LED?
Answer: 0 mcd.

Since candela and lumen are units that are adjusted to compensate for the varying sensitivity of the human eye to different wavelengths, and IR and UV are totally invisible (by definition) to the human eye, all IR and UV LEDs are automatically zero lumens and zero mcd. These units of measure, used for visible-light LEDs, can't be used for UV and IR LEDs (despite the "3000 mcd IR LED" currently on eBay).

IR and UV LEDs are measured in watts for radiant flux and watts/steradian for radiant intensity. A fairly typical "bright" IR LED will put out about 27 mW/sr, though they go up to 250 mW/sr or so. Signaling LEDs, like for TV remotes, are considerably less powerful.

HOWEVER - keep in mind that LEDs are not perfectly monochromatic. If their peak output is close to the visible spectrum, then their bandwidth may overlap the visible spectrum enough to be visible as a dim cherry-red light. Furthermore, some people can see further into the red region than can others, seeing as deep-red colors that to others are invisible infrared. While it would be possible to give such an LED a rating in millicandella, it would be misleading.

This dim red glow, by the way, is often claimed - wrongly - to differentiate good illumination IR LEDs from much dimmer IR LEDs. Which LED is better for such a purpose is totally dependant on the wavelength at which the receiver is most sensitive.

Using LEDs

As a rule of thumb, different color LEDs require different forward voltages to operate - red LEDs take the least, and as the color moves up the color spectrum toward blue, the voltage requirement increases. Typically, a red LED requires about 2 volts, while blue LEDs require around 4 volts. Typical LEDs, however, require 20 to 30 mA of current, regardless of their voltage requirements. The table on the left shows how much current a typical red LED will draw at various voltages.

Notice that this LED draws no current under 1.7 volts; the LED is "off". Between 1.7 volts and about 1.95 volts, the "dynamic resistance", the ratio of voltage to current, decreases to 4 ohms. Above 1.95 volts, the LED is fully "on", and dynamic resistance remains constant. Dynamic resistance differs from resistance in that the curve isn't linear. Just remember that this non-linear relationship between voltage and current means that Ohm's Law doesn't work for LEDs.

Notice how steep the slope is - almost vertical. LEDs have a much more vertical slope than do normal diodes (but not as bad as laser diodes).This means that a tiny increase in voltage can produce a large increase current, and lots of smoke. In the above-mentioned LED, 2 volts is required to drive the LED properly, but as little as 2.04 volts could destroy it. To keep the current down to a reasonable level, a series resistor must be included in the circuit.

The formula for calculating the value of the series resistor is:

R_series = (V - V_f) / I_f

where R_series is the resistor value in ohms, V is the supply voltage, V_f is the voltage drop across the LED, and I_f is the current the LED should see.

For example, the above LED would run very nicely off 12 volts with a 500 ohm series resistor. Since 500 ohms is an odd value, you could do almost as well with a 470 ohm resistor, which would let the LED draw 21 mA.

You can use a single resistor to control the current to a series of LEDs, in which case V_f is the total voltage drop across all the LEDs. You can sometimes get away with using a single resistor to control the current to a group of LEDs in parallel, but it's not generally a good idea - if there is any variation in the LEDs, they won't each draw the same current, resulting in differences in brightness - or in smoke.

Driving LEDs with AC

There are several factors to consider. One is that the LED will only conduct during that portion of the positive half of the cycle during which the voltage is above the threshold voltage of the LED. This means that the LED is conducting less than half the time, which will effect brightness.

Second, even when the LED is conducting, the average voltage will be far less than the peak voltage. The average voltage of the positive half of a sine wave is only 64% of the peak voltage. (Think "area under the curve.") Brightness is therefore further reduced.

This is what I mean. The X axis is time, the Y axis is voltage. The blue line is the supply voltage; the red line is the LED threshold. In this case, the peak voltage is 5 volts, and the threshold is 1.2 volts (typical for a red LED). The "effective voltage" (my term), is the voltage that is above the threshold voltage, the voltage that actually lights the LED; the rest of the voltage does nothing, either because it is under the threshold, or it's of the wrong polarity. Effective voltage is shown in the graph by the gray areas. The light gray area is the average effective voltage for an AC supply voltage; here, 1.04 volts. The dark gray area is the average effective voltage for a DC supply, 3.8 volts, that the AC supply voltage misses. The light gray area is a mere 27% of the area of both gray areas combined. If the LED had a threshold voltage of zero (wouldn't that be nice?) the effective AC voltage would still be only 32% of the effective DC voltage. As threshold voltage rises, the "duty cycle" goes down from there.

The effective voltage is the (V-V_t) term from the formula given above, and can replace it for calculating the value of the desired resistor.

You could increase the effective AC voltage toward the theoretical maximum of 32% of the effective DC voltage by increasing the supply voltage - this makes the threshold voltage a smaller portion of the peak voltage, so the LED turns on sooner in the cycle and stays on longer. But you have to avoid using a peak voltage greater than the reverse voltage that the LED can tolerate - typically only 5 volts. Remember that when the LED isn't conducting, all the voltage drop will be across the LED. You can sidestep this problem by including a separate diode - silicon diodes can withstand far more reverse voltage than LEDs can, although an additional diode will impose a second threshold voltage. Incorporating a full-wave bridge rectifier would let you drive the LED with both halves of the cycle, increasing the maximum possible effective voltage to 64% of that of DC, at the price of two additional threshold voltages.

Some white LEDs require forward voltages (typically 3.5 or 4 volts) very close to their maximum reverse voltage (typically 5 volts), so the LED will only be on for a very small fraction of the cycle, making it very dim. For example, an LED requiring 3.5 volts driven on 5 volts AC would only an effective AC voltage of only 0.25 volts, only 17% of the effective DC voltage of 1.5 volts.

To compensate for the low average effective voltage, we'd want to drive the LED pretty hard to get the average current up to 20 mA. If the effective voltage is only 0.25 volts, then the resistor should be 13 ohms, and the peak current will be 120 mA. Can the LED stand a peak of 120 mA? Probably not.

One possible solution is two LEDs in reverse-parallel, that is, one polarized to light during the positive half of the cycle, and the other polarized to light during the negative half. Right off the bat, this doubles the light output, since we're now using both halves"" alt align="right" width="234" height="207">f the cycle. Furthermore, since the only reverse voltage each LED will see is the forward voltage drop of the other LED, you can drive them with just about any voltage you want, so the "duty cycle" can approach 64% pretty closely. Using square-wave AC instead of sine-wave AC would let you reach almost 100%, either by using two reverse-parallel LEDs, or using one LED driven at twice the normal current for half the cycle.

---

Automotive Replacement  Bulbs:	Other Products:	Reference:
1156 1157 1142 2357 7507 7225 Bayonet Tail-Brake Turn Signal  Back Up	LED Light Fixtures & Strobes	Specs
3157 3156  3457 4157 3057 Wedge Tail-Brake-Turn Signal & Back-Up Bulbs	Lights For the Home, Yard & Garden	Cross Reference
7443 7440 Wedge Tail-Brake-Turn Signal & Back-Up Bulbs	Electrical Contacts, Sockets, Connectors & Fuses	Technical Data
194 168 2825 W5W Wedge Side Marker License Plate &  Interior Bulbs	Light Bright NEON Glow Wire	Bulb Dimensions
37 74 Gauge & Instrument Panel & Neo-Wedge  Bulbs	High Powered Leds	General Bulb Information
3022 3122 561 578 6418 6411 Festoon Dome Bulbs	LED & Neon Light Tubes	Application Charts
Ba9s, E10, Ba7s, Small Ba15s and Bay15d Bayonet Bulbs	MR11 & MR16 Bulbs	Bases & Filaments
906 921 Wedge Stop & Interior Bulbs	LED Flashlights Work lights & Bulbs	Shipping
Headlights & Foglights	LED Screw Mount Indicator & Accent  Lights	Mail Orders
HID Systems	Track Lights	International Shipping
LED Flashers, Protectors, Load Equalizers Turn Signal Fix	LED Light Fixtures for the Home & RV	FAQ'S
6 Volt Antique - Vintage Bulbs  & 24 volt	Windshield Washer LEDS
Marine Bulbs	Electrical Wire
Dura Chrome Titanium Platinum Silver Vision Bulbs	LED Bike, Go Ped, Motorcycle, ATV, Boat and RV Light Fixtures
Xenon Plasma Super Hyper White Bulbs	Miniature Train Bulbs & Parts
G4 T10 2 Pin Bi- Pin	Universal Programmable Remote Controllers & Switches for Garage Openers.
Semi, Truck & Truck Trailer Leds	Power Inverters  - Power Supplies  - Power Adapters
Overhead Lighting  - Trucks RV's and Under-Cabinets	Seat Covers
	Custom Car Graphics & Decals - Brake Caliper - Engine - Alloy Wheels
	Chrome Trim Products & Accessories
	LVD Electromagnetic Induction Bulbs

---

These Bulbs are Commonly Used in: Acura CL Integra Legend MDX NSX RL RSX SLX TL TSX Vigor Alfa Romeo Spider AMC Aston Martin Audi A3 A4 A6 A8 Allroad Cabriolet Q7 RS4 RS6 S4 S6 S8 TT Austin Austin Healey Bentley BMW 2002 3 Series 5 Series 6 Series 7 Series 8 Series M3 M5 M6 M Roadster & Coupe X3 X5 Z3 Z4 Z8 Buick Century Electra Grand National Lacrosse LeSabre Lucerne Park Avenue Rainier Reatta Regal Rendezvous Riviera Roadmaster Skylark Cadillac Allante Catera CTS DeVille Eldorado Escalade Fleetwood Seville SRX STS XLR Chevrolet Astro Avalanche Aveo Bel Air/150/210 Blazer C/K Pickup 1500 C/K Pickup 2500 C/K Pickup 3500 C-10 Camaro Caprice Cavalier Chevelle Cheyenne Cobalt Colorado Corsica Corvair Corvette El Camino Equinox Express G20 Van HHR Impala Lumina Malibu Monte Carlo Nova S-10 Silverado 1500 Silverado 2500 Silverado 3500 SSR Suburban Tahoe Tracker Trailblazer Uplander Venture Pickups Chrysler 300 Series Aspen Cirrus Concorde Crossfire Imperial LeBaron LHS New Yorker Newport Pacifica Prowler PT Cruiser Royal Sebring Town & Country Citroen Cord Daewoo Datsun Z-Series DeLorean DeSoto Dodge Avenger Caliber Caravan Challenger Charger Coronet Dakota Dart Durango Grand Caravan Intrepid Lancer Magnum Neon Nitro Power Wagon Ram 1500 Ram 2500 Ram 3500 Ram Van Shadow Sprinter Stealth Stratus Viper Pickups Eagle Edsel Ferrari 360 Fiat Ford Aerostar Aspire Bronco Bronco II Contour Crown Victoria Edge Escape Escort E-Series Van Excursion Expedition Explorer Explorer Sport Explorer Sport Trac F-100 F-150 F-250 F-350 Fairlane Fairmont Falcon Five Hundred Focus Ford GT Freestar FreeStyle Fusion Galaxie Model A Model T Mustang Probe Ranchero Ranger Taurus Tempo Thunderbird Torino Windstar Geo GMC Envoy Jimmy Safari Savana Sierra 1500 Sierra 2500 Sierra 3500 Sonoma Suburban Typhoon Yukon Honda Accord Civic CR-V CRX Del Sol Element Fit Insight Odyssey Passport Pilot Prelude Ridgeline S2000 Hummer H1 H2 H3 Hyundai Accent Azera Elantra Santa Fe Sonata Tiburon Tucson Infiniti FX G20 G35 I30 I35 J30 M Q45 QX4 QX56 International Harvester Scout Isuzu Amigo Rodeo Trooper VehiCROSS Jaguar E-Type S-Type XJ6 XJ8 XJR XJS XK8 X-Type Jeep Cherokee CJ Commander Commando Grand Cherokee Liberty Renegade Wagoneer Wrangler Kia Rio Sedona Sephia Sorento Spectra Sportage Lamborghini Lancia Land Rover Defender Discovery Freelander LR3 Range Rover Lexus ES GS GX IS LS LX RX SC Lincoln Aviator Continental LS Mark Series Navigator Town Car Zephyr & MKZ Lotus Elise Esprit Maserati Mazda 323 626 929 B-Series Pickups CX-7 Mazda3 Mazda5 Mazda6 Millenia MPV MX-3 MX-5 Miata MX-6 Protégé RX-7 RX-8 Tribute Mercedes Benz 190 Series 200 Series 300 Series 400 Series 500 Series 600 Series C Class CL Class CLK Class CLS Class E Class G Class M Class R Class S Class SL Class SLK Class SLR McLaren Mercury Capri Comet Cougar Grand Marquis Mariner Milan Montego Monterey Mountaineer Mystique Sable Tracer Villager MG MGA MGB Midget T-Series Mini Classic Mini Mini Cooper Mini Cooper S Mitsubishi 3000GT Diamante Eclipse Galant Lancer Mirage Montero Nash Nissan 200SX 240SX 280ZX 300ZX 350Z Altima Armada Frontier Maxima Murano Pathfinder Quest Sentra Stanza Titan Versa Xterra Oldsmobile 442 Alero Aurora Bravada Cutlass Eighty-Eight Intrigue Ninety-Eight 98 Silhouette Toronado Opel Packard Peugeot Plymouth Acclaim Barracuda Duster Fury Grand Voyager GTX Neon Prowler Road Runner Satellite Sundance Voyager Pontiac Bonneville Catalina Fiero Firebird G6 Grand Am Grand Prix GTO Le Mans Montana Solstice Sunbird Sunfire Tempest Trans Am Vibe Porsche 356 911 912 914 924 928 930 944 968 Boxster Cayenne Cayman Renault Rolls-Royce Saab 900 9000 9-2X 9-3 9-5 9-7x Saturn Ion L-Series S-Series Sky Vue Scion tC xA xB Shelby Studebaker Subaru Forester Impreza Legacy Outback SVX Tribeca Suzuki Toyota 4Runner Avalon Camry Celica Corolla FJ Cruiser Highlander Land Cruiser Matrix MR2 Paseo Previa Prius RAV4 Sequoia Sienna Solara Supra Tacoma Tercel Tundra Yaris Triumph Spitfire TR-6 Volkswagen Beetle (Pre-1998) Beetle - New (1998-Present) Bus Vanagon Cabrio EuroVan Golf Jetta Karmann Ghia Passat Phaeton Rabbit Thing Touareg Vanagon Volvo 240 740 850 940 C70 S40 S60 S70 S80 V40 V50 V70 XC Cross Country XC90 Willys